The iPhone 6 and iPhone 6 Plus jointly were themselves replaced as the flagship devices of the iPhone series by the iPhone 6s and iPhone 6s Plus on September 9, 2015. They are the eighth generation of the iPhone, succeeding the iPhone 5, iPhone 5c and iPhone 5s, and were announced on September 9, 2014, and released on September 19, 2014. The iPhone 6 and iPhone 6 Plus are smartphones that were designed and marketed by Apple Inc. brightness (typical), with dual-ion exchange-strengthened glassĦ: 8 MP (3264×2448 px max.) with 1.5 focus pixels, True Tone flash, autofocus, IR filter, burst mode, f/2.2 aperture, 1080p HD video recording (30 fps or 60 fps), slow-motion video ( 720p 120 fps or 240 fps), timelapse, panorama (up to 43 megapixels), face detection, stills from video, auto- HDR,Ħ Plus: In addition to above: optical image stabilization (for photos only) ġ.2 MP (1280×960 px max.), 720p video recording (30 fps), burst mode, f/2.2 aperture, exposure control, face detection, auto- HDR contrast ratio Īll models: 500 cd/m² max. h) lithium polymer battery Ħ: 4.7 in (120 mm) Retina HD: LED-backlit IPS LCD, 1334×750 px resolution (326 ppi) (128 px/cm) pixel density, 16:9 aspect ratio, 1400:1 typ.h) lithium polymer battery Ħ Plus: 3.82 V 11.1 W.PowerVR Series 6 GX6450 (quad-core), up to 136 GFLOPS Ħ: 3.82 V 6.91 W The corners are different and help to find the right position. Pay attention to the correct positioning of the adhesive frame. This way you avoid that something gets stuck on the adhesive frame. Do not remove the last small protective film until you have connected the display and attached the cover plates.Now remove the next large protective foil.You can use the plastic spudger for this. Do not press the adhesive frame firmly until you are sure that it is in place. From there, you can apply it to the device bit by bit. First place the adhesive frame on one edge of the case.Now you're ready to apply the new glue frame.This will ensure a proper fit of the adhesive frame. Remove the adhesive residue from the metal frame and display.iPhone 11 is very similar in its design, so the adhesive is applied in the same way. In the pictures we show you how to apply the adhesive frame using iPhone 8 as an example. To avoid overstretching the flexible cables, you can lean the display against a stable object or use the iHold.ĭo not open the display more than a little over 90 degrees to avoid damaging the sensitive flexible cables. Once you have passed around the device with the plectrum, you can now push the display upwards using the plectrum This will release the metal clamps from the frame. However, this can leave scratches on the frame. You can also use an iFlex instead of the hard plastic plectrum. This is especially important on the side of the standby button, as this is where the sensitive flex cables from the display are located. The tool should not be inserted further than about 5mm into the device to avoid damaging any components inside the iPhone. To remove the display adhesive, you must move the plectrum completely around the iPhone. At the same time, push the hard plastic plectrum between the case and display frame and press the case frame down. Use the key ring on the suction cup to lift the display. Now place the suction cup on the lower edge of the iPhone.To remove the glued screen from the frame, heat the edge of the display with your hairdryer to about 60° C (140° F) degrees.Is your glass very badly splintered? Then stick a strip of parcel tape on the glass in advance to protect yourself from splinters.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |